品薄のパナソニック製挿入機(アキシャル,ラジアル)ですが、弊社提携先に入荷しました。
今回も完売必至ですのでご興味のあるかたはお早めにお問い合わせください。
売り切れの際はご容赦ください。
No | 設備名 | 型式 | 画像① | 画像② |
1 | アキシャル挿入機 | AV131 モデル名:NM-EJA2A 仕様:60連 |
![]() |
![]() |
2 | アキシャル挿入機 | AV131 モデル名:NM-EJA3A 仕様:60連+60連 |
![]() |
![]() |
3 | ラジアル挿入機 | RG131 モデル:NM-EJR4A 仕様:80連 |
![]() |
![]() |
AV131は、 0.12 s /コンポーネントの タクトタイム で 高速挿入が可能なVCDアキシャルリードコンポーネント挿入機で、 高い経済効率を提供します。 複数の入力(120入力)と2つの独立した供給を可能にする垂直フィーダーの採用 稼働率を向上させるユニットであるAV131は、継続的な無人 運転に 大きく貢献することを約束してい ます。 また、オプションで利用可能なジャンパー線挿入機能により、ジャンパー線の挿入が可能になります。 テーピングの必要性。無駄をなくすだけでなく、非常に効率的で柔軟な生産を実現します。 |
特徴 |
より高い生産性 |
挿入タクトタイム |
コンポーネントあたり0.12秒での高速挿入により、生産性が大幅に向上します。 |
高速XYテーブル |
軽量で剛性の高い設計により、 |
高速XYテーブル。 |
4方向の挿入タクトタイム |
(0、90、180、270度) |
コンパクトで軽量な挿入ユニットとダイレクトドライブ |
中空シャフトモーターを採用したシステムは高速を提供します |
挿入ユニットが回転しているときの挿入。 |
2つの別個の部品供給ユニット(NM-EJA3A) |
2つのテーブルに分けられた部品供給ユニットにより、供給動作モードを以下に従って選択できます。 |
生産ニーズにより、稼働率が向上します。 (5つのモードが使用可能です。) |
ランダムアクセスシステム |
ランダムアクセスシステムでは、ボタンを操作するだけで挿入エラーをすばやく回復できます。 |
より高い信頼性 |
長寿命の消耗部品 |
リバーシブルテープカッターと |
リバーシブルリードカッター(固定側) |
これらの寿命を延ばす |
消耗部品。 |
挿入ガイドとプッシャー |
また、炭化物材料から作られた |
それらの長寿命を確保します。 |
円弧フラットケーブル |
円弧フラットケーブルを採用したヘッドとアンビル回転ユニットは、 |
可動部。 |
センタリング機能 |
テープの中心から外れたコンポーネントを修正するためのセンタリング機能は干渉を防ぎます |
コンポーネントと挿入プッシャーの間で、信頼性の高い挿入を実現します。 |
ダンパー式テープカッターユニット |
2.5 mmストローク(全部で5 mm)のダンパーを備えたテープカッターは、 |
異物が巻き込まれた場合のカッター。 |
標準機能としての全域自己補正機能 |
挿入位置にある2つの穴の両方を認識して、安定した最適な位置補正を行います |
挿入。 |
さらに、回転誤差と挿入ピッチの補正も可能になり、非常に正確になります |
より高い挿入率を提供する位置決め(XY、θおよびW)。 |
Power supply | • Rated voltage 3-phase 200 / 220 / 380 / 400 / 420 / | ||||
480 V selectable | |||||
• Frequency 50 / 60Hz | |||||
• Rated capacity Approx. 4kVA | |||||
Air supply | • Service air pressure 0.5 MPa | ||||
• Air consumption Approx. 150 L/min. (A.N.R) | |||||
Note: Quick coupler attached (SMC KK13P-03M, KK13S-03F). | |||||
Dimensions | • NM-EJA3A W4070 × D1910 × H1610 mm | ||||
(Not including signal tower) | |||||
• NM-EJA2A W2810 × D1910 × H1610 mm | |||||
(Not including signal tower) | |||||
Mass | • NM-EJA3A Approx. 2,520 kg (main body only) | ||||
• NM-EJA2A Approx. 1,750 kg (main body only) | |||||
Environmental requirements | • Ambient temperature 20°C ± 10°C | ||||
• Humidity 25 ~ 75%RH (with no condensation) | |||||
• Height above sea level 1,000 m or below | |||||
Transport and storage | • Ambient temperature -20 ~ 60°C | ||||
• Humidity 75%RH or less (with no condensation) | |||||
Operating controls | • Interactive operation via color LCD touch screen | ||||
(Front and Rear: Standard equipment) | |||||
English/Japanese/Chinese selectable with a single button | |||||
Recognition screen (displays the recognized board image | |||||
on a superimposed window) | |||||
Hierarchical menu (Operator/Engineer) | |||||
• I /O functions 3.5-inch FDD and SDD (standard equipment) | |||||
• Communication RS-232C | |||||
Coating color | • Standard color White: W-13 (G50) | ||||
Insertion tact time | • Max. tact time: 0.12 s/point | ||||
Max. tact time conditions by component type and insertion direction | |||||
Applicable | Axial lead | Jumper wire | |||
component | component | ||||
Insertion | |||||
direction | |||||
X (0°) | 0.15 s/point | 0.12 s/point | |||
Y (90°) | 0.12 s/point | 0.15 s/point | |||
-X (180°) | 0.15 s/point | - | |||
-Y (270°) | 0.24 s/point | - | |||
Other conditions for max. tact time (0.12 s/point) | |||||
• X-Y table movement | |||||
Within 35 mm for X and 39.5 mm for Y (When interlock 2 is selected) | |||||
(However, within 30 mm for X and 34 mm for Y when there are | |||||
components above 3 mm high on the PCB. (When interlock 1 is | |||||
selected)) | |||||
• Feeder movement | |||||
None | |||||
(When the feeder moves by 1 pitch, the tact time will be 0.14 s/point.) | |||||
Pitch changeover | • 5.3 mm within the tact time (0.12 s/point) | ||||
Applicable components | • Taped axial lead components | ||||
(carbon resistor, cylindrical ceramic capacitor, solid resistor, diode and | |||||
taped jumper wire) | |||||
• Jumper wire (optional) | |||||
Refer to `Insertion Component Specifications` in this section for | |||||
component dimensions. | |||||
Component packaging | • Flat pack | ||||
PCB replacement time | • Approx. 2 s (Ambient temperature: 20°C) | ||||
Applicable PCB | • Dimensions | ||||
Min. 50 × 50 mm to Max. 508 × 381 mm | |||||
Width-to-length ratio: Width should be equal to or less than length. | |||||
Consult us for boards having width longer than length. | |||||
• Allowable insertion area | |||||
Min. 50 × 40 mm to Max. 508 × 371 mm | |||||
• Thickness | |||||
1.6 ± 0.15 mm (for standard specification) | |||||
*1 Although boards of thicknesses from 0.6 mm (min.) to 2.0 mm (max.) | |||||
are applicable, changes to the transfer rail (option) are required | |||||
if outside the above standard range. | |||||
*2 Even if the board thickness is within the above range, clinched | |||||
angle of the inserted lead or lead length may vary, or board | |||||
transfer error may occur depending on the shapes of board or | |||||
insertion holes. So it is recommended to perform an advance | |||||
evaluation. | |||||
• Mass | |||||
Max. 1 kg per board including inserted components. | |||||
• Flow direction | |||||
Right to left (Standard) or Left to right (option) | |||||
• Board positioning method | |||||
Pin positioning (Standard, without positioning in the Y direction), | |||||
Edge positioning (Option, with positioning in the Y direction) | |||||
* Contact us for the board positioning in the Y direction. | |||||
Insertion pitch | • 5 ~ 26 mm (can be set in 0.01 mm increments) | ||||
(Jumper wire: 5 to 26 mm (Option)) | |||||
Insertion direction | • 4 directions (X, Y, -X and -Y) | ||||
Anvil | • Cutting & Clinch type system (Piezoelectric detection system | ||||
No. of component inputs | NM-EJA3A | ||||
1. Taping width: 26 mm | |||||
120 inputs (60 + 60) + drum type jumper wire (Option) | |||||
2. Taping width 52mm (Pack width Max. 80) | |||||
120 inputs (60 + 60) + drum type jumper wire (Option) | |||||
3. Mixed loading of 26 mm and 52 mm tapes is available. NM-EJA2A | |||||
1. Taping width 26 mm | |||||
60 inputs + drum type jumper wire (Option) | |||||
2. Taping width 52 mm (Pack width Max. 80) 60 inputs + drum type jumper wire (Option) | |||||
3. Mixed loading of 26 mm and 52 mm tapes is available. | |||||
Insertion height | • Insertion height programmable according to the component diameter | ||||
and lead diameter. | |||||
Clinching angle | • 15°to 30° inner clinching | ||||
Clinching length | • 1.5 ± 0.3 mm (Reference size: 1.5 mm)* | ||||
![]() |
|||||
*The above numerical range indicates the variation which arises due to | |||||
differences in the diameter or material of inserted component leads and in the diameter of holes of PCBs. | |||||
*When changing the clinching length (changing reference size), the anvil unit parts need to be replaced. (Individually supported) | |||||
=REMARKS= | |||||
1. A clinch mark will be left after cutting or clinching. | |||||
The shape of clinch mark varies with the lead diameter or material of the inserted component. | |||||
2. Clinched component will be tilted a maximum of ±10° in the | |||||
horizontal direction due to the hole diameter of PCB or accuracy of | |||||
hole position. | |||||
|
|||||